Rebirth 99 to become a car giant

Everyone in the industry has seen the level of Nanshan's gearbox.

So even if 4MT, 6MT and 4AT are shown, no one will feel particularly amazing.

After all, there are already 6AT cases placed there.

However, the introduction of Nanshan 1.5T turbocharged engine has caused a very big impact.

"Mr. Wang, I heard that this engine was specially researched by Nanshan for BYD's new car."

"Although I'm not sure what BYD's new model looks like, but if there is such an engine with very good power performance, coupled with the Nanshan gearbox, it may have a very big impact on the market."

"I think whether Great Wall Motor's engines will continue to be purchased from Aerospace Mitsubishi and Dong'an Power in the future, or whether it will speed up research progress by itself, needs to be reconsidered."

Almost all of Zhu Jianbo's attention today is on the engine.

Until now, the short board of Great Wall Motors lies in the engine.

Even for all domestic independent brands, engines are weak.

Although this short board can basically get all-round breakthroughs in the next 10 years, it was weak in 2003.

Among a group of weak chickens, a Tyrannosaurus rex suddenly appeared, which must have had a great impact on everyone.

"The Research Institute and Purchasing Department will contact Nanshan together and ask them for the specific parameters and prototype of this engine. We may consider using this product for our new models."

"The fuel consumption is lower and the power is stronger. As long as there is no problem with the quality, we have no reason not to use it."

"Of course, we have to speed up the research of the engine. If Nanshan can produce it, there is no reason why we can't produce it."

"We can even discuss with Nanshan to purchase a certain number of Nanshan engines, and then let them license our technology."

"It should be much easier to study the engine on this basis."

Wang Ying came to a conclusion without much hesitation.

There are good things, there is no reason not to use them.

"This estimate is a little difficult. They sell engines, and the business can continue."

"But if we directly authorize our technology, even if the authorization fee is relatively high, even if we directly purchase their engine technology, it will cost one or two hundred million at most."

"But there will be no business in the future."

"If the water keeps flowing, even if one engine only earns 1,000 yuan, as long as 100,000 units are produced, there will be a profit of 100 million yuan."

"According to the current development of the automobile market, we can basically consume 100,000 units a year."

Zhu Jianbo felt that if he were Nanshan, he would definitely not sell the engine technology he had just researched.

Even if a series of restrictions are given, they are reluctant to sell.

But Wang Ying didn't completely see it for himself, saying: "It doesn't hurt to try it, what if people agree?"

...

"Section Chief Fang, the people from Nanshan just introduced that the price of their die steel is only 200,000 a ton, which is almost half cheaper than the SKD11 imported from Dongying."

"Can your mold department consider verifying whether Nanshan Special Steel can meet our quality requirements?"

Liu Wei, director of the Purchasing Department of Xifeng Die Punching, also came to Yangcheng to participate in the Nanshan Science and Technology Day with Fang Wei, the chief of the mold department, and others today.

For them, they already have a good understanding of press and mold technology.

Both parties have already cooperated.

But in terms of mold steel, it can be regarded as one of the places they are most concerned about today.

As a stamping manufacturer, press equipment and molds are the two most important pieces of hardware.

Among them, in terms of press equipment, each stamping factory is generally outsourced, and it is difficult to reflect its core competitiveness.

Then it depends on the mold involved.

Except that most of PRG molds and TDM molds are still purchased from Nanshan, other TDM molds are produced by Xifeng Die Punching's own mold workshop.

In this case, the procurement of various special steels is naturally an inevitable thing in the process of making molds.

It is not that they have not tried to use die steel from domestic manufacturers such as Baosteel in the past.

It can barely be used on some parts with relatively low difficulty requirements and low precision requirements.

However, in the stamping process of high-strength steel plates, domestic die steel cannot meet the requirements.

Whether it is the stamping life of the die or the possibility of problems in the production process, everyone is not at the same level.

This is basically a common situation faced by domestic stamping manufacturers.

"From the current parameters of the mold steel they provide, there is no problem at all, and it is not worse than the imported SKD11 at all."

"In the next step, we will first purchase a small batch of mold steel from Nanshan, do some material testing, and try to use it to make several sets of molds."

"If there are no problems, it is natural to switch to Nanshan's mold steel, so that our mold costs can be reduced by at least 10%."

When Fang Wei left Nanshan, he was specially talked to.

He is now thinking that after three years have passed, he will find a way to return to Nanshan.

Especially seeing Nanshan's prosperous situation, he wanted to come back as soon as possible.

Besides, even if there is no such reason, he still supports the use of Nanshan special steel simply to reduce costs.

The premise is, of course, that the material meets the requirements.

"In the past, the group always came to check our localization rate and asked us if Xifeng Mochong had achieved 100% localization."

"I didn't have much confidence in the past, but now even the mold steel can be made in China, and our presses are also made in China."

"Then when the group asks us again in the future, they can confidently say that Xifeng Die Punching has achieved 100% localization."

When Liu Wei said this, Fang Wei wanted to add that some standard parts on the mold were still imported.

True 100% localization is still very difficult.

After all, when you get to the bottom of it, is the iron ore that you first used for these special steels imported?

...

"Mr. Cao, people from Huaxia TV are here."

When Cao Yang sent Liu Tianwu away and was about to chat with the general managers of other clients, Mi Ying quickly came over to report the new situation.

This Nanshan Science and Technology Day, Cao Yang just asked the sales department to invite various customers and potential customers.

For the media from all walks of life, there is really no special invitation.

After all, these technologies are all TO B, and do not need the help of the media to promote them too much, nor will they affect Nanshan's business development.

Didn't expect Huaxia TV to be interested in this situation?

Has the threshold for going to Huaxia TV become so low?

"Come on, let's go and have a look!"

In any case, the face of Huaxia TV must be given.

Cao Yang was going to go over to receive him in person.